I. Claydon , J. Turner , B. Sammakia ,
 Binghamton University, Binghamton, NY, USA
The ubiquitous nature of biofilms has led to a growing need to be able to detect, control, and maintain or remove them. Therefore a robust testing platform that allows for multiple analytical techniques is required to better understand their multitude of properties. The development of the self-contained microfluidic-based electrochemical cell portion of a multifaceted analysis system is ...
The Effect of Eccentricity in Fully Developed Annular Pipe Flow on Convection Heat Transfer and the Darcy Friction Factor
S. Rabbani , A. Elzawawy , J. D'Arrigo , J. D. Freels 
 Vaughn College of Aeronautics and Technology, New York, NY, USA
 Oak Ridge National Laboratory, Oak Ridge, TN, USA
Eccentricity in annular channels contributes to changes in fluid flow characteristics which in turn, affects the performance and integrity of the configuration. This research investigates a model of an annular channel with a diameter ratio of 0.762, an aspect ratio of 68.9:1 and heating of the internal surface of the inner cylinder with a 1.105MW/m2 heat flux. The Reynolds number ranges from 5 ...
E. Solomon and V. Mathew
Arcada University of Applied Sciences, Espoo, Finland
Three-dimensional flow analysis was performed by using COMSOL Multiphysics Chemical Engineering Module for the purpose of analyzing the flow properties and finding out the operating points of a test domain. Using material property table for an exemplary melt of LDPE (Low-Density Polyethylene), the logarithmic viscosity-shear rate graph was plotted and fitted to the 4–constant modified Carreau ...
B. Chinè , M. Monno
Laboratorio MUSP, Macchine Utensili e Sistemi di Produzione, Piacenza, Italy
Politecnico di Milano, Dipartimento di Meccanica, Milano, Italy
Instituto Tecnologico de Costa Rica, Cartago, Costa Rica
Introduction: In metal foams production, nucleated gas bubbles expand in a heated metal in a mold, then the foam cool and solidify. Thereby energy, mass and momentum transfer mechanisms are present simultaneously in the system and must be taken into account. Metal foam (Figure 1) can be obtained by foaming a precursor, i.e. a mixing of aluminum (Al) powders with the blowing agent TiH2, placing ...
N. Delmonte, F. Giuliani, P. Cova
Dipartimento di Ingegneria dell'Informazione, Università degli Studi di Parma, Parma, Italy
Introduction: Power electronic converters such as those for High Energy Physics Experiments (HEPEs) must operate in thermally hostile environment. Heat generated by electronics components must be conveniently dissipated to ensure electrical performances and improve reliability. Due to the high power density, the presence of closed environments, and the requirement of non-thermal interaction with ...
Fondazione Bruno Kessler (FBK), Renewable Energies and Environmental Technologies (REET) Unit, Trento, Italy
Concentrated photovoltaic systems with high efficiency solar cells are being widely investigated, aiming at improving the cost-efficiency balance in the solar energy field. Different cell types are in use: e.g., high concentration triple junction cells, reaching efficiencies of the order of 35 - 40 % at 1000 suns, and medium concentration mono-crystalline silicon cells, with efficiencies of the ...
J. Font-Capó, A. Nardi, M. Mendoza , E. Ruiz, S. Jordana, J. Molinero, P. Trinchero, J. Vargas
Amphos 21 Consulting, Barcelona, Spain
Amphos 21 Perú, Lima, Perú
Worley Parson/TWP, Lima, Perú
Some of the present metallic ores mines are located in areas formed by a heterogeneous fractured massif where groundwater flows preferentially through fractures. Underground mining in these zones can cause impacts in streams, lakes and change the natural water balance of the watersheds, leading to conflicts between traditional uses of water and the mining activity. Quantification of these ...
Priyanshu Goyal, I. Thangamani, V. Verma, V.M. Shanware, R. K. Singh
Bhabha Atomic Research Centre, Mumbai, India
In a nuclear reactor, the containment is the last barrier for the release of radioactivity during severe accident conditions. Containment material can be concrete or steel or steel-lined concrete. Steel containments have a high load bearing capacity and a high degree of leak tightness at higher pressures. In case of a severe accident, heat can be removed from the containment by a guide panel, ...
C. Butcher, K. Yu
University of Maryland, College Park, MD, USA
The complex internal flow field of a hypersonic air-breathing propulsion engine was modeled using COMSOL Multiphysics® software. This type of flow field can be found in a dual-mode scramjet engine. After creating the geometry, a 2D CFD simulation was run using the High Mach Number Flow physics interface in the CFD Module. A stationary time study was run and the results from the CFD simulation ...
E. Holzbecher, F. Sun
Georg-August Universität Göttingen, Göttingen, Germany
Within a borehole a nozzle can be installed in order to increase the efficiency of fluid injection. The position of the nozzle is located near the perforated casing of an injection well. A COMSOL Multiphysics® model is set up for a typical nozzle design as applied in practice. The model is based on the Navier-Stokes equations with turbulence closures using k-ε model and k-ω closures. We find a ...