Analysis of Heat Transfer in a Complex Three Dimensional Structure Fabricated by Additive Manufacturing - new
C. Settle, K. Hoshino
Biomedical Engineering Department, University of Connecticut, Storrs, CT, USA
The goal of this study was to create a three dimensionally designed biomedical device with multiple functionalities and analyze its simulated heat transfer. The device would be fabricated through additive manufacturing; specifically electron beam melting (EBM). EBM has a feature size constraint of 1 mm (acceptable for this design) and is only capable of manufacturing titanium alloys ; a ...
Optimization Module Enables Hybrid Experimental-Numerical Algorithm for 3D Particle Image Velocimetry - new
M. Sigurdson, C. Meinhart, I. Mezic
Department of Mechanical Engineering, University of California - Santa Barbara, Santa Barbara, CA, USA
In our study of chaotic mixing, 3D velocity measurements (u,v,w) are required for evaluation of a micro mixer using a mix-prediction algorithm. The hybrid approach presented here combines 2D measurements, an imperfect numerical model, and appropriate fitting parameters. Because our purpose is a measurement, rather than development of a physically accurate and predictive model, it not necessary ...
C. Soares, N. Padoin, A. C. Zimmermann, G. Cunha, P. B. Uliana, M. Wendhausen
Federal University of Santa Catarina, Florianópolis, SC, Brazil
PowerOpticks Technology Ltda, Florianópolis, SC, Brazil
In this study, COMSOL Multiphysics® software was applied to the investigation of the electromagnetic behavior of an optical crystal submitted to the magnetic field generated by electric current in a near positioned metallic conductor. Moreover, the influence of a ferromagnetic apparatus (magnetic concentrator) on the magnetic field acting upon the crystal was investigated. Three cases were ...
H. J. Hall , L. A. Starman ,
 Sensors Directorate, Air Force Research Laboratory, Wright-Patterson AFB, OH, USA
Beam steering and adaptive optics micromirror applications commonly demand optically flat surfaces with minimal mass. When reflective coatings (usually metallic Au or Al) are applied to micromirror surfaces in order to meet optical reflectivity requirements the resulting film stress (usually tensile) can be substantial. The mass of the mirror can be a limiting factor in the dynamic performance. ...
李晓南 , 刘国强 ,
利用惯性力学和电磁学，研究了一个金属小车沿着磁铁铺就的轨道做减速直线运动。其中，小车也可以看成是携带等量的磁铁剩磁，且沿着铁磁轨道减速运动。通过赋予小车一个初速度，例如100 m/s，然后再根据实际情况、赋予它一个特征密度，即小车有了一定的质量。当认为小车沿水平方向的轨道减速运动，忽略重力、空气阻力等其他一些影响因素时，小车将只受电磁的洛伦兹力的作用，而逐渐减速到零。 利用最新版的 COMSOL Multiphysics®，建模过程中，主要用到了“磁场和电场(mef)”和“全局常微分和微分代数方程(ge)”接口，涉及到的动力学和电磁学方程为 dv/dt=F/m F ⃗=∫_(V_vehicle)▒〖(J_induced ) ⃗×B ⃗dv〗 J_(i_y)=σ(v_z∙B_x-v_x∙B_z ) v 为小车即时速度，F 为洛伦兹力，J 为感应产生的涡流，v 为速度，B ...
D. Mi ,
 KEISOKU Engineering System Co., Ltd., Chiyoda-ku, Tokyo, Japan
Optimization of a typical electrochemical system with insulating shields is considered in this work, which objective is to reduce the current peak due to singularity and smooth the current density distribution along electrode surface. Moving mesh method was adopted to allow change in design variables, i.e., position and width of the insulating shields. It was found that combining optimization ...
COMSOL Multiphysics® Software: Simplifying Workflow and Promoting Innovations in Nuclear Engineering at ORNL
P. K. Jain , J. D. Freels ,
 Oak Ridge National Laboratory, Oak Ridge, TN, USA
At Oak Ridge National Laboratory (ORNL), COMSOL Multiphysics® software has become a preferred software for certain multiphysics applications in nuclear engineering. This presentation will highlight some of the ongoing activities in the following areas: (1) Highly enriched uranium (HEU) to low enriched uranium (LEU) conversion of the High Flux Isotope Reactor (HFIR), (2) New and improved safety ...
Establishing Tolerances and Limits of Failure for Sample and Reagent Flow Using COMSOL Multiphysics® Software
S. Kumar , D. Dendukuri 
Achira Labs, Bangalore, Karnataka.
Microfluidics is the science of manipulating and controlling fluids at the micron scale. Although, fluid flow in standard geometries can be determined easily by analytical methods, a more rigorous computational model is required for custom geometries. Achira’s microfluidics cartridge has a microchannel with intricate curvatures to allow the entrapment of biosensors. The number and dimensions of ...
Zhifang Li , Xiyang Zhang ,
 College of Photonic and Electronic Engineering, Fujian Normal University, Fuzhou, China
Laser immunotherapy (LIT) was developed to treat late-stage, metastatic cancers through local laser irradiation and immunological stimulation. In ILIT, the photothermal effect induces immune responses by destroying and interrupting tumor cells through temperature elevation in target tissue. Tumor is rich in vascularture, and plays a critical part in photothermal effect. Vascularized tumour ...
T. Roy,, P. Ranjan, , R. Balasubramaniam
Homi Bhabha National Institute, Mumbai, India
Bhabha Atomic Research Centre, Mumbai, India
Micro electrical discharge machining (MEDM), a scaled down version of EDM process, is a micro machining process used to fabricate micro holes and intricate shapes in electrically conductive materials irrespective of its hardness. In this process, an electric spark is generated in the gap between the two electrodes (tool as cathode and workpiece as anode) submerged in dielectric that leads to a ...